An oven that stays cold, takes forever to preheat or burns one side of the pan has a short list of likely causes, and a few of them you can rule out yourself. The list is different for electric and gas ovens, so start by knowing which one you have.
Start with the symptom
Three complaints sound similar and point in different directions. An oven that does not heat at all usually has a power, igniter or element problem. An oven that heats slowly or never reaches the set temperature usually has a worn element, a weak igniter or a sensor reading wrong. An oven that heats unevenly, with burnt edges and a pale center, is often a calibration, airflow or door seal issue. Note which of the three you have, because it narrows the search before you open anything.
Electric ovens
Bake element
The bake element is the heavy tube along the oven floor, and the broil element is the one at the top. When a bake element fails, you often see a blister, a break or a spot that never glows orange. Turn the oven on and look. If one of them stays dark while the other glows, that points to the element or its wiring. Replacing one is a standard repair, but the power has to be off at the breaker first, and many people prefer to have a company do it.
Temperature sensor
The slim probe at the back wall tells the control what the oven temperature is. If it drifts, the oven can overshoot or stop short. A sensor that is out of range can make an oven cook hot or cold by a wide margin without any visible damage.
Control board and relays
On many modern ovens, a relay on the control board switches the elements. A clicking sound with no heat, a blank display or error codes can point there. This is a part where a repair company has diagnostic tools that a homeowner does not.
Power supply
Electric ranges run on a 240-volt circuit with two breakers ganged together. If one half trips, the cooktop can seem to work while the oven does not heat, or the reverse. Check the panel for a breaker that sits halfway between on and off, and switch it fully off and then on.
Gas ovens
Igniter
Most gas ovens use an electric glow-bar igniter that heats up and opens the gas valve. As it ages, it glows but draws too little current to open the valve, so you hear nothing and get no flame. This is the most common reason a gas oven will not heat, and it is the most common repair on older gas ranges.
Safety valve and flame sensing
If the igniter glows but gas never lights, or the flame lights and dies, the valve or sensor may be the issue. This is gas work. Do not take gas components apart yourself.
If you smell gas
Leave the house, call 911 from outside and then call your gas utility. Do not turn anything on or off, and do not try to relight the oven. Xcel Energy's emergency number is 1-800-895-2999, and other Colorado gas utilities have their own, which our guide on what to do when you smell gas lists. If a carbon monoxide alarm sounds, get everyone outside and call 911.
Uneven baking in either type
- Door gasket. A torn or flattened gasket lets heat escape and creates cool spots near the door. Look for gaps or burnt-through sections.
- Calibration. An oven that reads 25 degrees off may be fixable through the control menu. Check your manual for the offset setting.
- Convection fan. A convection oven with a fan that does not turn will bake unevenly. A dragging or noisy fan motor needs attention.
- Rack position and pans. Dark pans absorb more heat, foil covering the floor blocks airflow and a crowded rack throws off circulation. Move food to the middle rack and use light-colored pans for an easy test.
- Preheating. Most ovens beep before they are truly steady. Give them another ten minutes before loading a delicate bake.
Safe checks before you call
- Confirm the clock and mode. A locked control, sabbath mode, a timer program or a demo mode can all prevent heating.
- Check the breaker or, for a gas oven with an electric igniter, confirm the outlet has power by seeing whether the clock works.
- Look at the elements on an electric oven for breaks or blisters with the power off.
- Test with an oven thermometer on the middle rack, since the display and the real temperature can differ.
- Remove anything stored in the oven, such as a pan or foil, that could block air or touch an element.
- Run a self-clean cycle only if the manual says to, and expect some failures to show up after one, since the cycle runs very hot.
Stop if you see sparking, melted wires, a burning smell or anything that makes you uneasy. Turn the breaker off and call a company.
Altitude and baking in the Denver area
Sometimes the oven is fine and the recipe is the problem. Water boils at a lower temperature as elevation rises, and CSU Extension's table gives about 212F at sea level, 203F at 5,000 feet and 198F at 7,500 feet. It states no Denver-specific figure. Lower boiling temperatures mean liquid evaporates faster and batters set differently, which is why cakes can dome, dry out or collapse in the Denver area when a recipe was written for sea level. If your bakes fall flat but the oven holds temperature on a thermometer, look at an altitude-adjusted recipe before blaming the oven.
Gas ovens are affected a different way. A Maytag range installation manual says that above 2,000 feet, burner ratings are reduced at a rate of 4 percent for each 1,000 feet above sea level. Many ranges are set up for a certain altitude, and a unit that was not adjusted can burn with a lazy yellow flame or heat slowly. Our guide to gas appliances at altitude covers the symptoms. Conversion work is a job for a qualified company, not a do-it-yourself project.
Cleaning and use habits that cause trouble
Spills that bake onto the oven floor can smoke and trip a sensor, and heavy cleaner left on an element can pit it. Wipe the door glass and gasket gently, since scrubbing a gasket flat shortens its life. Do not line the oven floor with foil on models that have a hidden bake element, because it can trap heat and damage the element or the floor panel. Check the manual for what your model allows.
What repairs cost and when replacing makes sense
We do not have Denver-specific prices. National averages from HomeGuide put the typical appliance repair at about $100 to $400 and a service call alone at about $70 to $130, and each company sets its own prices. An igniter or element is generally at the lower end of what an oven repair can cost, while a control board lands higher.
NAHB lists life expectancy at 17 years for electric ranges and 19 for gas ranges. An oven well past that age with a failed control board is a good candidate for replacement, while a ten-year-old with a bad element is usually worth fixing. Our repair or replace guide includes the half-the-cost rule of thumb, and the repair cost guide collects the sourced ranges.
What happens when you call
This site is a free referral service, not a repair company. You are connected with an independent local appliance repair company serving the Denver area. It sets its own prices and schedule. Be ready with the brand, the model and serial number from the label inside the door frame or behind the drawer, whether the oven is gas or electric, and what the oven does and does not do.
Our service pages cover oven repair, wall oven repair and range repair in more detail. For town pages, try Arvada or Parker, or read the whole guide library.
Frequently asked questions
Why is my electric oven not heating?
Why will my gas oven not light?
Does altitude affect oven baking in Denver?
Is it worth repairing an old oven?
Sources
Last updated: